The Toyota Sienna maintenance light reset depends on your model year and engine, so match your van to a source before you press any button.
The steps below cover 2004, 2007 and 2009 Siennas from third-party repair manuals, plus the 2026 Sienna from Toyota’s own owner’s manual. For 2011 to 2025 vans no button steps were confirmed, so use the manual for your year.
Toyota Sienna Maintenance Light Reset by Model Year
The Toyota Sienna maintenance light reset sequence changes with the model year and engine, and this guide has steps for 2004, 2007, 2009 and 2026. Each row of the table applies to that year and engine, not to the others.
| Model year | Engine and drive | Start sequence | Hold and finish |
|---|---|---|---|
| 2004 | 3.3L V6 (3MZ-FE), AWD | Odometer in ODO mode, ignition ON then OFF | Hold trip RESET while turning ON; light blinks, then goes off |
| 2007 | 3.5L V6 (2GR-FE), AWD | Ignition in ACC or LOCK with odometer shown | Hold trip reset while turning ON for at least 5 seconds, until 000000 |
| 2009 | 3.5L V6 (2GR-FE), FWD | Ignition in ACC or LOCK with odometer shown | Hold trip reset while turning ON, until 000000 (no hold time given) |
| 2011 to 2025 | Not covered here | Not covered here | Check Toyota’s owner’s manual for your model year |
| 2026 | Hybrid, 7-inch or 12.3-inch display | Meter control switches, settings menu, press and hold OK | Select Scheduled Maintenance, then Yes |
Before any Toyota Sienna maintenance light reset, confirm the model year on your registration or title, and check the engine and drive against the row. If they do not match, the steps do not apply, even when the year is the same.
If your van is a 2026 model, skip to the Toyota manual section later in this guide. The steps for one row do not carry over to another, even when the trip button looks the same.
Reset Steps for the 2004 Sienna (3.3L V6)
On a 2004 Sienna with the 3.3L V6, the reset starts with the trip display in ODO mode and finishes with a second ignition cycle. The steps come from a third-party workshop manual page for the 2004 AWD model with the 3MZ-FE engine.
- Turn the ignition to ON.
- Set the odometer and trip display to the ODO mode.
- Turn the ignition to OFF.
- Press and hold the trip meter RESET button while you turn the ignition to ON.
- Watch the light. It stays solid for 3 seconds, blinks for 2 seconds, stays solid for 1 second, then turns off.
- Release the RESET button.
- Turn the ignition to OFF.
- Turn the ignition to ON. The light should stay off.
Compare what you see with each light change in order, because each step matters for this 2004 Toyota Sienna maintenance light reset. Do not skip the light check in step five.
If the light keeps blinking during the 2004 Toyota Sienna maintenance light reset, turn the ignition off and start again from step one. The same page says part of the procedure was taken from a Toyota bulletin, so it may not match the full revised version.
Toyota issued bulletin 00203 for the 2004 Sienna, covering a service maintenance reminder light reset. The public summary does not list the steps, so see the bulletin 00203 summary for the scope; ask a dealer for the full text if the sequence fails.
Reset Steps for the 2007 AWD Sienna (3.5L V6)
On a 2007 AWD Sienna with the 3.5L V6, you hold the trip meter reset button while the key turns to ON, until the odometer shows 000000. This sequence comes from a third-party repair manual page for the 2007 AWD model with the 2GR-FE engine, and it takes three steps.
- With the odometer displayed, turn the ignition key to ACC or LOCK.
- Turn the key to ON while you press and hold the trip meter reset button.
- Keep holding the button for at least 5 seconds, until the odometer shows 000000 and the light goes off.
The page does not say where the trip reset button sits. According to the same page, if the reset does not take, the light keeps flashing. This 2007 Toyota Sienna maintenance light reset has no blinking sequence to watch, so the 5-second hold is the step to get right.
Reset Steps for the 2009 Sienna (3.5L V6)
On a 2009 front-wheel-drive Sienna with the 2GR-FE V6, the trip meter method follows the 2007 pattern, but the source gives no hold time. Use these steps for a 2009 Toyota Sienna maintenance light reset only if your van is a FWD model.
- Set the ignition to ACC or LOCK while the odometer is displayed.
- Press and hold the trip meter reset button, then turn the engine switch to ON.
- Keep holding the button until the trip meter shows 000000.
Vehicles with navigation use a different path, so the Toyota Sienna maintenance light reset differs from the trip method. The same page says the maintenance item is reset with the INFO button and the Maintenance screen, not the trip meter, so check the menu names in your owner’s manual before you start.
Toyota Sienna Maintenance Light Reset in the 2026 Owner’s Manual
On the 2026 Sienna, Toyota’s 2026 Sienna owner’s manual says to reset the maintenance message from the multi-information display after the required service is done. The 2026 Toyota Sienna maintenance light reset uses the steering wheel meter control switches, not the trip button used on older vans.
With the 7-inch display
- Use the meter control switches on the steering wheel to select the settings icon on the multi-information display.
- Select the next icon in the menu, then press and hold OK.
- Select Scheduled Maintenance and press OK.
- Select Yes and press OK. A confirmation message appears on the display.
With the 12.3-inch display
- Press and hold OK to show the cursor on the center content area of the display.
- Use the meter control switches to select the settings icon, then press OK.
- Select the next icon in the settings path and press OK.
- Select Scheduled Maintenance and press OK.
- Select Yes and press OK.
The Toyota Sienna maintenance light reset and the oil reset are separate items in the manual. After an oil change, the same menu path leads to Oil Maintenance instead of Scheduled Maintenance, and you confirm with Yes. The manual refers to a separate Scheduled Maintenance Guide or Owner’s Manual Supplement for service intervals.
The manual covers the 2026 model only, so no Toyota Sienna maintenance light reset steps from it apply to earlier vans. For a 2011 to 2025 van, this guide did not confirm the button steps, so look for the section titled Resetting the message indicating maintenance is required in the owner’s manual for your year before you press anything.
What the Light Means Before You Reset It
The maintenance light counts distance since the last service, so reset it only after the oil change or other service is finished. Before any Toyota Sienna maintenance light reset, confirm that the work is done, because resetting early leaves the reminder wrong for the next interval.
- The 2007 page says the lamp lights for about 3 seconds at about 4,500 miles after an oil change, then flashes for about 12 seconds with the key on.
- Past 5,000 miles without an oil change, the same page says the lamp stays on.
- On the 2026 Sienna, the manual says “Maintenance Required Soon” comes on about 4,500 miles (7,200 km) after the last reset and “Maintenance Required Visit Your Dealer” about 5,000 miles (8,000 km) after it. The manual adds that the indicator does not work properly unless the message has been reset.
- The Toyota Sienna maintenance light reset clears the reminder count only, so keep receipts for each service.
Other Toyota models use different menus; see the Toyota 4Runner maintenance light reset steps or the Tacoma maintenance light reset guide if you also own one.
When the Light Stays On After a Reset
If the light stays on or keeps flashing after a Toyota Sienna maintenance light reset, repeat the sequence once, then check the 2004 bulletin or a dealer. A flashing light after the 2007 sequence means the reset did not take, according to that page. On a 2026 van, the manual says “Engine Maintenance Required Visit Your Dealer” points to a malfunction, so have the van inspected right away.
If another warning light is on with the maintenance light, do not assume it is only a service reminder. A different warning light needs a code read or a dealer check before you go further.
Frequently Asked Questions
Does the 2026 Sienna use the same reset as older vans?
No. The 2026 owner’s manual uses the multi-information display menu and the Scheduled Maintenance item, not the trip button. This guide did not confirm the steps for 2011 to 2025 vans, so use the manual for your model year.
Does resetting the light change my service record?
The sources used here describe the reset as clearing the reminder only. None of them says the reset records the work, so keep receipts for oil changes and other service in your own file.
Is the maintenance light the same as the oil light?
On the 2007 page, the maintenance light works as an oil change reminder. The 2026 manual lists Scheduled Maintenance and Oil Maintenance as two separate reset items, so check which message your dashboard shows.
Can I reset the light without a dealer tool?
For the Toyota Sienna maintenance light reset steps above, yes. The older vans use the ignition key and the trip button, the 2026 van uses the meter control switches, and none of the sources mention dealer software.
Why do the steps differ by year?
Each year and engine can use a different reset path, so each needs its own procedure. This guide only has sources for the four years listed above.
If your Sienna is a 2011 to 2025 model, do not rely on the steps in this guide. Before any Toyota Sienna maintenance light reset, the manual for your year is the right source, and you should reset the light only after the service is finished.
